Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Hasimir0

Pages: [1] 2 3 4
1
Installation / Re: Help Installing P6
« on: September 28, 2015, 02:30:32 am »
After setting up the USB using dd it all worked fine.
Thanks a lot! :D


2
Installation / Re: Help Installing P6
« on: September 24, 2015, 02:52:17 am »
It worked, thanks! :D
Now dd should have written the p6.iso on the usb drive.
Can I just try and install it or is there anything else I should do first?

3
Installation / Re: Help Installing P6
« on: September 23, 2015, 09:56:09 am »
OK dd must be slightly different on a mac .. skip

try
Code: [Select]
sudo dd if=/Users/hasimir/downloads/Peppermint-6-20150904-i386.iso of=/dev/disk3 bs=1048576

result was
Code: [Select]
dd: /dev/disk2: Resource busy(yes disk2 is correct, for some reason diskutil this time detected the usb device there :P )

4
Installation / Re: Help Installing P6
« on: September 23, 2015, 03:43:28 am »
so I checked my directories and devices and this is the code I came up with

Code: [Select]
sudo dd if=/Users/hasimir/downloads/Peppermint-6-20150904-i386.iso of=/dev/disk3 bs=1M
But the terminal says

Code: [Select]
dd: bs: illegal numeric value

5
Installation / Re: Help Installing P6
« on: September 23, 2015, 12:34:24 am »
not too comfortable, but avoiding a disaster should not be too hard
running diskutil list I see all disks and partitions.
all system partitions and disks are /dev/disk0 and  /dev/disk1 with various partitions such as  /dev/disk0s1 or  /dev/disk0s2
the usb device is read as  /dev/disk2 with its main partition being  /dev/disk2s1


6
Installation / Re: Help Installing P6
« on: September 22, 2015, 04:26:50 pm »
mmm... nope...
after I run Unebootin it clearly says that I can't use that bootable USB device with a Mac :(
but yes, OSX recognises both dd and cat
I have no other computers (only another mac) but I can get a hold of another usb drive if needed

7
Installation / Re: Help Installing P6
« on: September 22, 2015, 01:24:41 pm »
yes I installed both p4 and p5 using that usb key: sundisk 16gb from a few years ago
it works perfectly (as far as moving files around is concerned, at least).

to prepare it for Unebootin I formatted it using my MacBookPro Disk Utility.
I erased it, with the name "Peppermint6" the format "MS-DOS FAT" and the scheme "Master Boot Record"
Then run Unebootin using the ISO for p6 32-bit (MD5 checked out fine)

8
Installation / [SOLVED] Unetbootin Problems
« on: September 22, 2015, 12:01:45 pm »
Hi :)
I'm trying to install P6 (32-bit) on an old Asus eee-pc 1025.
The old OS got messed up beyond recognition after some failed installation attempts of other OSs and then got "cleaned up" using the dd command.
Now I created a P6 boot usb drive using my MacBookPro ... but when I insert the usb device in the eee-pc and boot the machine I get this error

Reboot and Select proper Boot device
or Insert Boot Media in selected Boot device and press a key

I did go into the BIOS and select the USB device as primary boot... but I still get this error.

Help?  :-\

9
Odd that Opera works as it now uses the same "blink" layout engine as Chrome/Chromium.
Which version of Opera are you running ?

Sorry for the loooong delay... I'm running the latest 32bit Opera, which is Version 12.16 Build 1860 ... all newer versions are exclusively 64bit ç_ç

10
Thanks for the support!

I guess I'll stick to Chromium and occasionally use Opera when the problem appears to be too insistent :\

11
Code: [Select]
  *-display               
       description: VGA compatible controller
       product: Atom Processor D2xxx/N2xxx Integrated Graphics Controller
       vendor: Intel Corporation
       physical id: 2
       bus info: pci@0000:00:02.0
       version: 09
       width: 32 bits
       clock: 33MHz
       capabilities: pm msi vga_controller bus_master cap_list rom
       configuration: driver=gma500 latency=0
       resources: irq:43 memory:dfd00000-dfdfffff ioport:f0c0(size=8)

PS: happy holidays :D

12
nope, apparently the problem is back... I don't know why :(
this Aw Snap crap happens at random times whenever I watch a YouTube video.

13
Everything seems to work fine, so THANKS A LOT :D

Only one weird thing... it seems like the "Aw Snap!" still appears on YouTube only at the end of a single video; I mean if I see a list of videos, one ends and the subsequent starts and all is fine. But when I look a single video, when it ends and the screen tries to load the mosaic with all the other related videos, that's when the Aw Snap strikes.

It's definitely a minor issue I can live with :)
But I'm curious... what could the problem be? o_O

14
Code: [Select]
# Default settings for chromium-browser. This file is sourced by /bin/sh from
# /usr/bin/chromium-browser

# Options to pass to chromium-browser
CHROMIUM_FLAGS=""

# part for pepperflashplugin-nonfree : begin

flashso="/usr/lib/pepperflashplugin-nonfree/libpepflashplayer.so"

if [ -f $flashso ]
then
        flashversion=`strings $flashso|grep ^LNX|sed -e "s/^LNX //"|sed -e "s/,/./g"`
        CHROMIUM_FLAGS="$CHROMIUM_FLAGS --ppapi-flash-path=$flashso --ppapi-flash-version=$flashversion"
fi

# part for pepperflashplugin-nonfree : end

. /usr/lib/pepflashplugin-installer/pepflashplayer.sh

15
So...
- F5 didn't work
- Ctrl+Shift+N didn't work
- disable-gpu finally seemed to work ... except on Tumblr, but I managed to figure out that the problem was my "Lazarus" extension

so, I do I make the disable-gpu thingie become my default way of launching any Chromium window? :D

Pages: [1] 2 3 4